MM GRIT-16K/18P :  MULTI-MASTER interchangeable solid carbide small diameter, groove milling heads. "P" suffix for sharp cutting edge. "K" suffix for T-land on cutting edge, to be used on cast iron.  
 
 
Internal groove milling Side slotting
  Designation
D
W±0.02
Tmax
Z
r		 D
minMinimum bore diameter
Ts
  Grade
  MM GRIT 16K-1.50-0.10  15.70  1.50  2.80  3  0.10  16.00  T06 IC528
  MM GRIT 16P-1.50-0.10  15.70  1.50  2.80  3  0.10  16.00  T06 IC528
  MM GRIT 16K-1.57-0.20  15.70  1.57  2.80  3  0.20  16.00  T06 IC528
  MM GRIT 16K-2.00-0.20  15.70  2.00  2.80  3  0.20  16.00  T06 IC528
  MM GRIT 16P-2.20-1.10  15.70  2.20  2.80  3  1.10  16.00  T06 IC528
  MM GRIT 16K-2.39-0.20  15.70  2.39  2.80  3  0.20  16.00  T06 IC528
  MM GRIT 16K-2.50-0.20  15.70  2.50  2.80  3  0.20  16.00  T06 IC528
  MM GRIT 16K-3.00-0.20  15.70  3.00  2.80  3  0.20  16.00  T06 IC528
  MM GRIT 16P-3.00-0.20  15.70  3.00  2.80  3  0.20  16.00  T06 IC528
  MM GRIT 16K-3.17-0.20  15.70  3.17  2.80  3  0.20  16.00  T06 IC528
  MM GRIT 18K-1.20-0.05  17.70  1.20  3.80  3  0.05  18.00  T06 IC528
  MM GRIT 18P-1.20-0.60  17.70  1.20  3.80  3  0.60  18.00  T06 IC528
  MM GRIT 18K-1.40-0.05  17.70  1.40  3.80  3  0.05  18.00  T06 IC528
  MM GRIT 18K-1.50-0.10  17.70  1.50  3.80  3  0.10  18.00  T06 IC528
  MM GRIT 18K-1.57-0.20  17.70  1.57  3.80  3  0.20  18.00  T06 IC528
  MM GRIT 18K-1.70-0.05  17.70  1.70  3.80  3  0.05  18.00  T06 IC528
  MM GRIT 18K-2.00-0.20  17.70  2.00  3.80  3  0.20  18.00  T06 IC528
  MM GRIT 18P-2.00-1.00  17.70  2.00  3.80  3  1.00  18.00  T06 IC528
  MM GRIT 18P-2.20-1.10  17.70  2.20  3.80  3  1.10  18.00  T06 IC528
  MM GRIT 18K-2.39-0.20  17.70  2.39  3.80  3  0.20  18.00  T06 IC528
  MM GRIT 18K-2.50-0.20  17.70  2.50  3.80  3  0.20  18.00  T06 IC528
  MM GRIT 18K-3.00-0.20  17.70  3.00  3.80  3  0.20  18.00  T06 IC528
  MM GRIT 18P-3.00-1.50  17.70  3.00  3.80  3  1.50  18.00  T06 IC528
  MM GRIT 18K-3.17-0.20  17.70  3.17  3.80  3  0.20  18.00  T06 IC528

Tightening torque: 1000 N.cm.
For clamping instructions, click on "More Info".
Modification options on request.
Recommended for O-rings and retaining rings.
Do not apply lubricant to the threaded connection.
K-For general steel machining.
P-Positive geometry for soft and gummy materials.
Print  Send by mail  Save to word  Save to Excel


Terms of Use and Legal Disclaimer