PARTING
NPA 37/2018 INCH
New PVD Coated Inserts for Machining ISO P & M Materials
(Steel & Stainless Steel)
Highlights
ISCAR is launching new tough PVD grades for parting applications on carbon steels, alloyed steels and stainless steels: IC1010 for medium to high speeds and IC1030 for low to medium speeds.
The new grades are based on TiAlN coating which significantly improves toughness and wear resistance, assuring longer tool life.
Both grades exhibit better resistance at unstable conditions and interrupted cut. The new grades are available on TANG-GRIP and DO-GRIP inserts.
IC1030 (M25-M45) (P30-P45)
IC1030 - TiAlN coating overlays the very tough substrate IC28 for wide range of applications at high feeds and low to medium speeds. The grade is recommended for interrupted cut and machining at unstable conditions.
The cutting parameters should be same as for IC830.
IC1010 ISO (M15-M30) (P15-P30)
IC1010 - TiAlN coating overlays the sub-micron grade IC08. It is recommended for general parting and grooving applications with medium to high cutting speeds and low to medium feeds.
The cutting parameters should be the same as for IC808.
IC1030 is intended to replace and phase out gradually older grades IC328 and 928.
IC1010 will replace and phase out IC308 and IC1028 grades.
The current insert range with IC1010 and IC1030 grades is introductory and IC1010 and IC1030 will be expanded in the near future.
Machining Range Speed and Feed
Wear Resistance
Toughness
Toughness
Continuous Cut
Moderate Cut
Interrupted Cut
Application Range - Material Groups
First Choice Hard Tough Steel Stainless Steel Cast Iron Aluminum High Temp. Alloys Hardened Steel
Customer Test Report for IC1030
Application: Parting hexagonal, Stainless Steel 316L bars .866”
Target: Increasing insert tool life
Insert | TAG N3J IC830 ISCAR |
TAG N3J IC81030 ISCAR |
---|---|---|
Grade | IC830 | IC1030 |
Cutting speed (SFM) | 490 | 490 |
Feed (inch/rev) | .004 | .004 |
Depth of cut (inch) | .43 | .43 |
Material | Stainless steel 316 | Stainless steel 316 |
Application | Haxagonal bar | Haxagonal bar |
Parts per edge | 80 | 160 |
100% Improvement in Tool Life!
Customer Test Report for IC1010
Application: Parting C15E Steel bars 1.3”
Target: Increasing insert tool life
Insert | DGN 3102C IC808 ISCAR |
DGN 3102C IC1010 ISCAR |
---|---|---|
Grade | IC808 | IC1010 |
Cutting speed (SFM) | 490 | 490 |
Feed (inch/rev) | .006 | .006 |
Depth of cut (inch) | .65 | .65 |
Material | Steel C15E | Steel C15E |
Application | Round bar | Round bar |
Parts per edge | 2500 | 4000 |
60% Improvement in Tool Life!
Field Tests IC1010 – Summary of Weighted Results
TOOL LIFE IMPROVEMENT
IC1010 Vs IC808
Typical Wear Differences (Same cutting conditions and time)
Field Tests IC1030 – Summary of Weighted Results
TOOL LIFE IMPROVEMENT
IC1030 Vs IC830
Typical Wear Differences (Same cutting conditions and time)
DGN/DGNM-J/JS/JT
Double-Sided Inserts for Parting and Grooving Soft Materials, Parting Tubes, Small Diameters and Thin-Walled Parts
Double-Sided Inserts for Parting and Grooving Soft Materials, Parting Tubes, Small Diameters and Thin-Walled Parts
(1) Sharp corners
(2) Single-ended insert
(3) No depth limit
DGN/DGNC/DGNM-C
Double-Sided Parting Inserts for Parting and Grooving Bars, Hard Materials and Tough Applications
Double-Sided Parting Inserts for Parting and Grooving Bars, Hard Materials and Tough Applications
(1) Inserts with coolant holes, recommended coolant pressure 145PSI minimum
(2) Single-ended insert.
(3) No depth limit
DGN-Z
Double-Sided Inserts for Parting Tubes, Thin-Walled and Small Parts
Double-Sided Inserts for Parting Tubes, Thin-Walled and Small Parts
DGN-LF/LFT
Double-Sided Inserts for Parting and Grooving Stainless Steel
Double-Sided Inserts for Parting and Grooving Stainless Steel
Most suitable for soft materials at low to medium feeds
DGN-MF
Double-Sided Inserts for Parting and Grooving Soft and Hard Materials at Medium Feeds
Double-Sided Inserts for Parting and Grooving Soft and Hard Materials at Medium Feeds
TAG N-C/W/M
Single-Ended Inserts for Parting, Grooving and Slitting Bars, Hard Materials and Tough Applications
Single-Ended Inserts for Parting, Grooving and Slitting Bars, Hard Materials and Tough Applications
(1) Larger corner radii for interrupted cut and high feed applications
(2) Similar to C-type, but with a modified edge; improved chip control at medium feeds
TAG N-J/JS/JT
Single-Ended Inserts for Parting, Grooving and Slitting Soft Materials
Single-Ended Inserts for Parting, Grooving and Slitting Soft Materials
(1) Sharp corners cannot be used on TGSF slitting cutters
TAG N-LF
Single-Ended Inserts for Parting, Grooving and Slitting Stainless Steel
Single-Ended Inserts for Parting, Grooving and Slitting Stainless Steel
TAG N-MF
Single-Ended Inserts for Parting, Grooving and Slitting Stainless and Alloy Steel at Medium Feed
Single-Ended Inserts for Parting, Grooving and Slitting Stainless and Alloy Steel at Medium Feed
The NPA37-INCH-2018's pdf file: View (PDF) or Download (ZIP)