Page 14 - FAST_FEED_MILL_Brochure_INCH_2022

LF OAL
DC

FFT3 EFM-MM 02 DCX THSZMS DCONMS Rd°
Small Diameter Endmills with
a MULTI-MASTER Threaded
Adaptation Carrying Triangular APMX 14˚
Inserts for Fast Feed Milling

Designation DCX (1) DC APMX AE (2) CICT (3) LF DCONMS THSZMS OAL DRVS (4) RMPX° (5) MDN (6) MDX (7) MIID (8) TQ (9) Lbs
FFT3 EFMD08/.31-2MMT05-02 .315 .087 .0236 .114 2 .394 .299 T05 .659 .217 10.8 .402 .591 FFT3 TXMT 0201205T 4.50 .02
FFT3 EFMD10/.39-3MMT06-02 .394 .165 .0236 .114 3 .394 .382 T06 .642 .315 4.7 .559 .748 FFT3 TXMT 0201205T 4.50 .02
• Radius for programing .043" • To generate a straight surface without cusps, the width of cut must not exceed DC
(1) Cutting diameter maximum
(2) Maximum plunging width
(3) Number of inserts
(4) Torque key size
(5) Maximum ramping angle
(6) Machinable diameter minimum for interpolation
(7) Machinable diameter maximum for interpolation
(8) Master insert identification
(9) Recommended tightening torque (lbf*in) for insert screw

Spare Parts

Designation
FFT3 EFM-MM 02 SR M2X0.4-2.9 T6-HG T-6/5 MAGNET 3X3

FFT3 EFM-02 LH OAL
Small Diameter Endmills LU Rd°
Carrying Single-Sided Triangular DCX DC DCONMS
Inserts for Fast Feed Milling
APMX
14˚

Designation DCX (1) DC APMX AE (2) CICT (3) LU LH OAL DCONMS Shank (4) RMPX° (5) MDN (6) MDX (7) MIID (8) TQ (9) Lbs
FFT3 EFM D08-2-060-C10-02 .315 .087 .0236 .114 2 .6693 .787 2.362 .394 C 10.8 .402 .591 FFT3 TXMT 0201205T 4.50 .07
FFT3 EFM D08-2-080-C12-02 .315 .087 .0236 .114 2 1.0236 1.181 3.150 .472 C 10.8 .402 .591 FFT3 TXMT 0201205T 4.50 .11
FFT3 EFM D10-3-070-C10-02 .394 .165 .0236 .114 3 .7677 .787 2.756 .394 C 4.7 .559 .748 FFT3 TXMT 0201205T 4.50 .09
FFT3 EFM D10-3-090-C12-02 .394 .165 .0236 .114 3 1.1811 1.299 3.543 .472 C 4.7 .559 .748 FFT3 TXMT 0201205T 4.50 .13
• Radius for programming .043 inch • To generate a straight surface without cusps, the width of cut must not exceed DC
(1) Cutting diameter maximum
(2) Maximum plunging width
(3) Number of inserts
(4) C-Cylindrical
(5) Maximum ramping angle
(6) Machinable diameter minimum for interpolation
(7) Machinable diameter maximum for interpolation
(8) Master insert identification
(9) Recommended tightening torque (lbf*in) for insert screw

Spare Parts
Designation
FFT3 EFM-02 SR M2X0.4-2.9 T6-HG (a) T-6/5 MAGNET 3X3
(a)

14 FAST FEED MILLING