Page 16 - FAST_FEED_MILL_Brochure_INCH_2022

OAL
LF

FFT3 EFM-MM 03 A DC Rd°
Endmills with a MULTI-MASTER DCX THSZMS DCONMS
Threaded Adaptation Carrying APMX
Single-Sided Small Trigon 17° DRVS
Inserts for Fast Feed Milling

Designation DCX (1) DC APMX AE (2) CICT (3) LF DCONMS THSZMS OAL DRVS (4) RMPX° (5) MDN (6) MDX (7) MIID (8) Lbs
FFT3 EFMD10/.39-2MMT06-03 .394 .220 .0236 .087 2 .394 .382 T06 .642 .315 6.9 .614 .748 FFT3 WXMT 030206T .04
FFT3 EFMD12/.47-3MMT08-03 .472 .299 .0236 .087 3 .591 .461 T08 .886 .394 4.7 .772 .906 FFT3 WXMT 030206T .07
FFT3 EFMD16/.63-4MMT10-03 .630 .457 .0236 .087 4 .787 .602 T10 1.232 .512 2.9 1.087 1.220 FFT3 WXMT 030206T .11
FFT3 EFMD.75-5-MMT12-03 .750 .580 .0236 .087 5 .984 .710 T12 1.508 .630 2.0 1.330 1.460 FFT3 WXMT 030206T .00
FFT3 EFMD20/.78-5MMT12-03 .787 .614 .0236 .087 5 .984 .748 T12 1.508 .630 2.0 1.402 1.535 FFT3 WXMT 030206T .15
FFT3 EFMD25/.98-6MMT15-03 .984 .811 .0236 .087 6 1.181 .945 T15 1.850 .787 1.5 1.795 1.929 FFT3 WXMT 030206T .00
FFT3 EFMD1.00-6-MMT15-03 1.000 .830 .0236 .087 6 1.181 .960 T15 1.850 .787 1.5 1.830 1.960 FFT3 WXMT 030206T .25
• Radius for programming .043" • To generate a straight surface without cusps, the width of cut must not exceed DC
(1) Cutting diameter maximum
(2) Maximum plunging width
(3) Number of inserts
(4) Torque key size
(5) Maximum ramping angle
(6) Machinable diameter minimum for interpolation
(7) Machinable diameter maximum for interpolation
(8) Master insert identification

Spare Parts

Designation
FFT3 EFM-MM 03 TS 18041I/HG TS 18041I/HG (a) T-6IP/51
(a) Recommended tightening torque: 4.5 lbfxin

FFT3 EFM-03 A LH OAL
Endmills Carrying Single- Rd°
Sided Small Trigon Inserts DCX DC DCONMS
for Fast Feed Milling
APMX
17° A

Designation DCX (1) DC APMX AE (2) CICT (3) LH OAL DCONMS Shank (4) RMPX° (5) MDN (6) MDX (7) MIID (8) Lbs
FFT3 EFMD.38-2-3.0C.38-03 .375 .200 .0236 .086 2 .750 3.000 .375 C 7.5 .575 .711 FFT3 WXMT 030206T .08
FFT3 EFMD.50-3-5.0C.50-03 .500 .325 .0236 .086 3 1.000 5.000 .500 C 4.0 .823 .961 FFT3 WXMT 030206T .24
FFT3 EFMD.62-4-5.5C.62-03 .625 .450 .0236 .086 4 1.250 5.500 .625 C 2.5 1.075 1.211 FFT3 WXMT 030206T .40
• Radius for programming .043" • To generate a straight surface without cusps, the width of cut must not exceed DC
(1) Cutting diameter maximum
(2) Maximum plunging width
(3) Number of inserts
(4) C-Cylindrical
(5) Maximum ramping angle
(6) Machinable diameter minimum for interpolation
(7) Machinable diameter maximum for interpolation
(8) Master insert identification

Spare Parts

Designation
FFT3 EFM-03 TS 18041I/HG (a) T-6IP/51
(a) Recommended tightening torque: 4.5 lbfxin

16 FAST FEED MILLING