Page 16 - Turning_catalog_INCH_2022_45_P509-690

PARTING DGTR/L-B/BC-D DGTL-BC-D CWN-CWX H LH HBH H B WB
DGTL-B-D
Integral Shank Reinforced Parting
and Grooving Tools Especially
OAL
for DGNC Type of Inserts
WF
CDX
Designation CWN (3) CWX (4) H B WB OAL LH CDX (5) WF HBH CSP (6) Left-hand shown
Insert
DGTR/L 9.5B-1.4D20 .055 .055 .375 .375 .039 5.500 .930 .394 .360 .10 0 DG. 14..
DGTR/L 12.7B-1.4D30 .055 .055 .500 .500 .039 5.500 1.200 .591 .480 .11 0 DG. 14..
DGTR/L 16B-1.4D30 .055 .055 .630 .630 .039 5.512 1.165 .591 .610 - 0 DG. 14..
DGTR/L 19B-1.4D30 .055 .055 .750 .750 .039 5.500 1.200 .591 .730 - 0 DG. 14..
DGTR/L 9.5B-2D30 .075 .100 .375 .375 .063 5.500 1.200 .591 .340 .24 0 DG. 1.../DG. 2..
DGTR/L 12.7B-2D30 .075 .100 .500 .500 .063 5.500 1.200 .591 .470 .24 0 DG. 1.../DG. 2..
DGTR/L 16B-2D32 .075 .098 .630 .630 .063 5.512 1.205 .630 .598 - 0 DG. 1.../DG. 2..
DGTR/L 19B-2D35 .075 .100 .750 .750 .063 5.500 1.300 .689 .720 - 0 DG. 1.../DG. 2..
DGTR/L 25.4B-2D35 .075 .100 1.000 1.000 .063 5.500 1.300 .689 .970 - 0 DG. 1.../DG. 2..
DGTR/L 12.7B-3D30 .118 .125 .500 .500 .094 5.500 1.200 .591 .450 .11 0 DG. 1.../DG. 3..
DGTR/L 16B-3D35 .118 .125 .630 .630 .094 5.512 1.264 .630 .583 .10 0 DG. 1.../DG. 3..
DGTR/L 16BC-3D35 (1) .118 .125 .630 .630 .094 5.512 1.224 .630 .583 .10 1 DGNC/DGRC/DGLC 3...
DGTR/L 19BC-3D40 (1) .118 .125 .750 .750 .094 5.500 1.400 .787 .700 .10 1 DGNC/DGRC/DGLC 3...
DGTR/L 19B-3D40 (2) .118 .125 .750 .750 .094 5.500 1.400 .787 .700 - 0 DG. 1.../DG. 3..
DGTR/L 25.4B-3D40 (2) .118 .125 1.000 1.000 .094 5.500 1.400 .787 .950 - 0 DG. 1.../DG. 3..
DGTL 25.4BC-3D40 (1) .118 .125 1.000 1.000 .094 5.500 1.400 .787 .950 - 1 DGNC/DGRC/DGLC 3...
DGTR 25.4BC-3D40 (1) .118 .125 1.000 1.000 .094 5.500 1.400 .780 .950 - 1 DGNC/DGRC/DGLC 3...
• Important: 1.4 mm (.055") width inserts should be used only on tools for 1.4 mm specific width tools
• DGN/R/L 1 mm (.039") inserts can also be mounted into pocket sizes 2 and 3.
• For insert depth capacity table and modification instructions for the 2 and 3 holder pockets, see page 531 • For user guide,see pages 594-603
(1) Tools for inserts with coolant holes for high temperature alloys and stainless steel
(2) Insert's Tmax=.7", for deeper penetration modify insert into single-ended
(3) Minimum cutting width
(4) Maximum cutting width
(5) The specified limit refers to the tool
(6) 0 - Without coolant supply, 1 - With coolant supply
For inserts, see pages: DGN-LF/LFT (537) • DGN-P (539) • DGN-UT/UA (539) • DGN-WP (540) • DGN-Z (538) • DGN/DGNC/DGNM-C (533)
• DGN/DGNM-J/JS/JT (535) • DGR-P (540) • DGR-WP (541) • DGR-Z/ZS (538) • DGR/L-C DGRC/LC-C (534) • DGR/L-J/JS (536)

Spare Parts

Designation
DGTR/L 9.5B-1.4D20 SR M5X12 DIN912 HW 4.0
DGTR/L 12.7B-1.4D30 SR M5X12 DIN912 HW 4.0
DGTR/L 16B-1.4D30 SR M5X12 DIN912 HW 4.0
DGTR/L 19B-1.4D30 SR M5X12 DIN912 HW 4.0
DGTR/L 9.5B-2D30 SR M5X12 DIN912 HW 4.0
DGTR/L 12.7B-2D30 SR M5X12 DIN912 HW 4.0
DGTR/L 16B-2D32 SR M4X14 DIN912 HW 3.0
DGTL 19B-2D35 SR M5X12 DIN912 HW 4.0
DGTR 19B-2D35 SR M4X14 DIN912 HW 3.0
DGTL 25.4B-2D35 SR M5X12 DIN912 HW 4.0
DGTR 25.4B-2D35 SR M4X14 DIN912 HW 3.0
DGTR/L 12.7B-3D30 SR M5X12 DIN912 HW 4.0
DGTR/L 16B-3D35 SR M5X12 DIN912 HW 4.0
DGTR/L 16BC-3D35 SR M5X12 DIN912 HW 4.0 CGM 343* CF 343* SGCU 341* CGF 343*
DGTR/L 19BC-3D40 SR M5X12 DIN912 HW 4.0 CGM 343* CF 343* SGCU 341* CGF 343*
DGTR/L 19B-3D40 SR M5X12 DIN912 HW 4.0
DGTR/L 25.4B-3D40 SR M5X12 DIN912 HW 4.0
DGTR/L 25.4BC-3D40 SR M5X12 DIN912 HW 4.0 CGM 343* CF 343* SGCU 341* CGF 343*
* Optional, should be ordered separately

524 ISCAR